Skip to content
Send an enquiry

Stainless steel materials as precision strip

We hold more than 20 of these materials in stock. We source many more materials on request. The tables give the European material number and the American designation. Which thickness and width is available for each grade is available on request.

Alloying elements such as chromium, nickel, molybdenum, manganese, silicon and iron flow into a glowing steel melt

Austenitic grades

Austenitic steels cannot be hardened by quenching, but they can be work-hardened. They are highly resistant to corrosion and form well. They are the largest group and also provide the spring strip.

Material no.AISI / UNSIn-house abbreviation
1.4301304K304PS, K304
1.4303305K305
1.4306304LK304L10
1.4307304LK304L
1.4310301K301, K301Mo
1.4311304LN-
1.4372201K201
1.4401316K316
1.4404316LK316L
1.4435316LK316L(HP)
1.4436316K316S
1.4438317LK317L
1.4539904LK904L
1.4541321K321
1.4547S31254K254SMO
1.4565S34565-
1.4571316TiK316Ti

Ferritic grades

Ferritic steels are magnetic, form well and are predominantly chromium-alloyed. They usually contain little or no nickel.

Material no.AISIIn-house abbreviation
1.4000410SK410S
1.4003410L-
1.4016430K430
1.4017-K431
1.4113434K434
1.4509441K441Li
1.4510439K439
1.4512409K409
1.4520430Ti-
1.4521444K444
1.4526436K436

Martensitic grades

Martensitic steels can be hardened. They become strong and wear-resistant, for example for blades.

Material no.AISIIn-house abbreviation
1.4006410K410
1.4021420K420A
1.4028420K420B
1.4034420K420C

Heat-resistant grades

These steels are made for continuous use at high temperatures.

Material no.AISI / UNSIn-house abbreviation
1.4828309K309
1.4833309SK309S
1.4835S30815-
1.4841314K314
1.4845310SK310S

Duplex and precipitation-hardening

Duplex steel is stronger than the austenitic grades and highly resistant to corrosion. The precipitation-hardening steel 1.4568 reaches very high strength after heat treatment and is used for springs.

Material no.AISI / UNSIn-house abbreviation
1.44622205K318LN
1.4568631 (17-7 PH)K631

What is in stock?

The matrix under Stock shows which materials we hold in stock in which thickness.

Comparison table of the materials

The table sets all grades side by side, with European material number, American designation, our in-house abbreviation and the chemical composition according to the standard.

GroupMaterial no. (EN)NoteASTMIn-house abbreviationStandardC %Cr %Ni %Mo %Si %Mn %P %S %N %Cu %Ti %Nb %Other
Ferritic1.4000-410SK410SEN 10088-2≤ 0.08012.0-14.0--≤ 1.00≤ 1.00≤ 0.040≤ 0.015-----
Ferritic1.4003-410L-EN 10088-2≤ 0.03010.5-12.50.30-1-≤ 1.00≤ 1.50≤ 0.040≤ 0.015≤ 0.03----
Martensitic1.4006-410K410EN 10088-20.08-0.1511.5-13.5≤ 0.75-≤ 1.00≤ 1.50≤ 0.040≤ 0.015-----
Ferritic1.4016-430K430EN 10088-2≤ 0.08016.0-18.0--≤ 1.00≤ 1.00≤ 0.040≤ 0.015-----
Ferritic1.4016-430-EN 10088-2≤ 0.08016.0-18.0--≤ 1.00≤ 1.00≤ 0.040≤ 0.015-----
Ferritic1.4017--K431EN 10088-2≤ 0.08016.0-18.01.20-1.60-≤ 1.00≤ 1.00≤ 0.040≤ 0.015-----
Martensitic1.4021C = 0.16 - 0.25 %420K420AEN 10088-20.16-0.2512.0-14.0--≤ 1.00≤ 1.50≤ 0.040≤ 0.015-----
Martensitic1.4021C = 0.16 - 0.25 %420-EN 10088-20.16-0.2512.0-14.0--≤ 1.00≤ 1.50≤ 0.040≤ 0.015-----
Martensitic1.4028C = 0.26 - 0.35 %420K420BEN 10088-20.26-0.3512.0-14.0--≤ 1.00≤ 1.50≤ 0.040≤ 0.015-----
Martensitic1.4028C = 0.26 - 0.35 %420-EN 10088-20.26-0.3512.0-14.0--≤ 1.00≤ 1.50≤ 0.040≤ 0.015-----
Martensitic1.4034C = 0.43 - 0.50 %420K420CEN 10088-20.43-0.5012.5-14.5--≤ 1.00≤ 1.00≤ 0.040≤ 0.015-----
Ferritic1.4113-434K434EN 10088-2≤ 0.08016.0-18.0-0.90-1.40≤ 1.00≤ 1.00≤ 0.040≤ 0.015-----
Austenitic1.4301Ni > 9.0 %304K304PSEN 10088-2≤ 0.07017.5-19.58.0-10.5-≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4301-304K304EN 10088-2≤ 0.07017.5-19.58.0-10.5-≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4303-305K305EN 10088-2≤ 0.06017.0-19.011.0-13.0-≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4306-304LK304L10EN 10088-2≤ 0.03018.0-20.010.0-12.0-≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4307C ≤ 0.03 %304LK304LEN 10088-2≤ 0.03017.5-19.58.0-10.5-≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4310Ni > 6.5 %301K301EN 10088-20.05-0.1516.0-19.06.0-9.5≤ 0.80≤ 2.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4310Ni > 7.0 %301-EN 10088-20.05-0.1516.0-19.06.0-9.5≤ 0.80≤ 2.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4310Mo > 0.7 %301K301MoEN 10088-20.05-0.1516.0-19.06.0-9.5≤ 0.80≤ 2.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4311Ni > 9.2 %304LN-EN 10088-2≤ 0.03017.5-19.58.5-11.5-≤ 1.00≤ 2.00≤ 0.045≤ 0.0150.12-0.22----
Austenitic1.4372Ni > 3.5 %201K201EN 10088-2≤ 0.15016.0-18.03.5-5.5-≤ 1.005.5-7.5≤ 0.045≤ 0.0150.05-0.25----
Austenitic1.4372Ni > 4.0 %201-EN 10088-2≤ 0.15016.0-18.03.5-5.5-≤ 1.005.5-7.5≤ 0.045≤ 0.0150.05-0.25----
Austenitic1.4401-316K316EN 10088-2≤ 0.07016.5-18.510.0-13.02-2.50≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4404C ≤ 0.03 %316LK316LEN 10088-2≤ 0.03016.5-18.510.0-13.02-2.50≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4435-316LK316L(HP)EN 10088-2≤ 0.03017.0-19.012.5-15.02.50-3≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4436-316K316SEN 10088-2≤ 0.05016.5-18.510.5-13.02.50-3≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Austenitic1.4438-317LK317LEN 10088-2≤ 0.03017.5-19.513.0-16.03.0-4.0≤ 1.00≤ 2.00≤ 0.045≤ 0.015≤ 0.10----
Duplex1.4462Duplex2205K318LNEN 10028-7-21.0-23.04.5-6.52.50-3.5-≤ 2.00--0.10-0.22----
Ferritic1.4509-441K441LiEN 10088-2≤ 0.03017.5-18.5--≤ 1.00≤ 1.00≤ 0.040≤ 0.015--0.10-0.60[3xC+0.30]-1-
Ferritic1.4510similar to 430Ti, Cr > 17.0 %439K439EN 10088-2≤ 0.05016.0-18.0--≤ 1.00≤ 1.00≤ 0.040≤ 0.015--[4x(C+N) + 0.15]--
Ferritic1.4512-409K409EN 10088-2≤ 0.03010.5-12.5--≤ 1.00≤ 1.00≤ 0.040≤ 0.015--[ 6x (C+N)]-0.65--
Ferritic1.4520similar to 434, Cr > 16.0 %430Ti-EN 10088-2≤ 0.02516.0-18.0--≤ 0.50≤ 0.50≤ 0.040≤ 0.015≤ 0.02-[4x(C+N) + 0.15]-0.80--
Ferritic1.4521-444K444EN 10088-2≤ 0.02517.0-20.0-1.80-2.50≤ 1.00≤ 1.00≤ 0.040≤ 0.015≤ 0.03-[4x(C+N) + 0.15]-0.80--
Ferritic1.4521Ni > 0.015 %444-EN 10088-2≤ 0.02517.0-20.0-1.80-2.50≤ 1.00≤ 1.00≤ 0.040≤ 0.015≤ 0.03-[4x(C+N) + 0.15]-0.80--
Ferritic1.4526Super ferritic436K436EN 10088-2≤ 0.08016.0-18.0-0.80-1.40≤ 1.00≤ 1.00≤ 0.040≤ 0.015≤ 0.04--[7x(C+N)+0.10 ]-1-
Austenitic1.4539-904LK904LEN 10088-2≤ 0.02019.0-21.024.0-26.04.0-5.0≤ 0.70≤ 2.00≤ 0.030≤ 0.010≤ 0.151.20-2---
Austenitic1.4541-321K321EN 10088-2≤ 0.08017.0-19.09.0-12.0-≤ 1.00≤ 2.00≤ 0.045≤ 0.015----Ti: 5 × C to 0.70
Austenitic1.4547-S31254K254SMOEN 10088-2≤ 0.02019.5-20.517.5-18.56.0-7.0≤ 0.70≤ 1.00≤ 0.030≤ 0.0100.18-0.250.50-1---
Austenitic1.4565-S34565-EN 10088-2≤ 0.03024.0-26.016.0-19.04.0-5.0≤ 1.005.0-7.0≤ 0.030≤ 0.0150.30-0.60---Nb: 0.15
Precipitation-hardening1.4568-631K631EN 10088-2≤ 0.09016.0-18.06.5-7.8-≤ 0.70≤ 1.00≤ 0.040≤ 0.015----Al: 0.70-1.50
Austenitic1.4571-316TiK316TiEN 10088-2≤ 0.08016.5-18.510.5-13.52-2.50≤ 1.00≤ 2.00≤ 0.045≤ 0.015----Ti: 5 × C to 0.70
Heat-resistant1.4828-309K309EN 10095-19.0 - 21.0011.0 - 13.00-1.50 - 2.50-≤ 0.045≤ 0.015-----
Heat-resistant1.4833-309SK309SEN 10095-22.0 - 24.0012.0 - 14.00---≤ 0.045≤ 0.015-----
Heat-resistant1.4835-S30815-EN 100950.05-0.1220.0 - 22.0010.0 - 12.00-1.40 - 2.50max. 1.00≤ 0.045≤ 0.0150.12 - 0.20---Ce: 0.03 - 0.08
Heat-resistant1.4841-314K314EN 10095-24.0 - 26.0019.0 - 22.00-1.50 - 2.50-≤ 0.045≤ 0.015-----
Heat-resistant1.4845-310SK310SEN 10095-24.0 - 26.0019.0 - 22.00---≤ 0.045≤ 0.015-----

If your grade is missing

Tell us the material, dimensions and quantity. We source and slit.

Enquire about a grade