How precision strip is made
Precision strip starts as a melt in the steelworks and ends up with you as a single coil or spool. Here you can see the route in eleven steps.
Not every strip goes through all steps. Which ones apply depends on grade, thickness and surface. Spring strip, for example, is additionally work-hardened; bright strip is annealed under protective gas.
Learning video · stainless steel precision strip
From scrap to precision strip
Step 01 / 11
Tap to enlarge
Step 01 · Raw material
Scrap and alloys
- Stainless steel is a recycled material. The scrap share of the charge is plant-specific and often high.
- The scrap is sorted by grade, e.g. 1.4301 or 1.4404, and checked by spectrometer.
- What is missing is added as ferroalloys: ferrochrome, ferronickel, molybdenum.
- Corrosion resistance rests on a thin, chromium-rich passive layer that forms on a clean surface in the presence of oxygen.
Step 02 · Melting
Melting in the arc furnace
- Three graphite electrodes strike arcs. Melting time depends on the furnace and the charge material.
- The slag binds impurities and protects the melt.
- The result is a pre-melt – its carbon content is still too high.
Step 03 · Secondary metallurgy
Decarburisation in the AOD converter
- An argon-oxygen mixture is blown into the melt through nozzles below the bath surface.
- Argon favours decarburisation with limited chromium oxidation. Afterwards a large part of the oxidised chromium is recovered from the slag.
- Afterwards the melt is desulphurised and the analysis fine-tuned, e.g. for 1.4310 or 1.4404.
Step 04 · Casting
Continuous casting into slabs
- The melt flows from the ladle via the tundish into a water-cooled copper mould.
- The strand solidifies from the outside in, is bent into the horizontal and cut into slabs.
- Slabs are inspected and, where needed, ground to remove surface defects.
Step 05 · Hot forming
Hot rolling into coil
- Slabs are heated in the furnace to approx. 1,200 to 1,280 °C.
- High-pressure water removes the scale, then the mill stand rolls the slab thinner in several passes.
- The hot strip (approx. 2 to 8 mm) is coiled up into a coil.
Step 06 · Heat treatment
Annealing and pickling
- For suitable austenitic grades: solution annealing at approx. 1,050 to 1,150 °C followed by rapid cooling. Carbides dissolve and the microstructure becomes uniform.
- The scale is broken up by shot blasting and pickled off in mixed acid (nitric/hydrofluoric acid).
- Result: hot rolled, heat treated, pickled.
Step 07 · Cold forming
Cold rolling to size
- Rolling takes place at room temperature in several passes, e.g. on 20-high mills, with intermediate annealing where needed.
- For precision strip, precision mills with automatic gauge control follow – tolerances in the µm range (EN ISO 9445).
- The strip work-hardens. Depending on the degree of rolling, strengths up to spring-hard are obtained (EN 10151).
Step 08 · Setting properties
Bright annealing
- Depending on the temper and surface required, annealing takes place under a protective atmosphere (hydrogen/nitrogen): no scale forms and the surface stays bright.
- Recrystallisation softens the strip again. Cold rolling can then continue.
- Intermediate annealing between rolling passes, final annealing for the end condition – or deliberately no annealing for spring-hard tempers.
- Not every final condition passes through this step: 2B is annealed, pickled and lightly skin-passed, 2H stays work-hardened.
Step 09 · Flatness
Levelling
- Rolling and annealing leave residual stresses: the strip is wavy or tends to camber.
- In stretch-bend levelling, the strip is bent under high tension over staggered small rolls and is slightly elongated plastically in the process.
- Braking and tension bridle rolls build up the strip tension. A strip levelled flat can then be slit cleanly. Residual stresses are reduced, not eliminated entirely.
Step 10 · Processing to size
Slitting to width
- The mother coil runs through circular knives on two knife shafts – upper and lower knives cut like scissors.
- One coil yields many narrow slit strips in a single pass.
- Aim: tight width tolerance, little camber, low-burr edges. Edges can optionally be deburred or rounded.
Step 11 · Quality
Test, document, dispatch
- Dimensions, flatness and surface are checked against the standard and the customer specification.
- The tensile test determines the tensile properties. Hardness testing and chemical analysis of the heat provide additional results.
- The scope of tests and data in the inspection certificate depends on the standard and the order. The strip then goes to the customer as a single coil or spool.
We know the right partner for every step
The steelworks carry out the first steps. We do not do everything ourselves, but we usually know who is best at which step, and we put your strip together from this. How we work
Your strip, your size
Tell us the material, thickness, width and quantity. We will check what we can slit from stock or source.